Styler, S1000D, and Foldouts
I have a question regarding the sequence of numbering in Styler. I have a description Data Module to which I have added Division to levelledPara. I styled figure as a Formal Block. Problem 1: With...
View ArticleCreo Quality Agent won't install
Creo quality agent fails to install at 36%. Tried many times. Made sure to run setup as admin and turned of antivirus. When I run creo parametric, it says I need to register the quality agent. I...
View ArticleClik here to view.
License Request Failed for Feature
Problem Outline:This problem is characterized by an error message that appears right after PTC Creo 2.0 launches. The error appears in a Creo window named "Warning: Message List" and typically has a...
View ArticleClik here to view.
Any Understanding of the following error message
Hi any one have any idea as to why when i open a project the following error message flags up whichs states 'Object reference not set to an instance of an object' ?
View ArticleCreo Layout
I have 2 questions. 1. I have assembled a *.cem (creo layout 2.0) but I can's see any of the lines I sketched in creo layout 2.0. 2. I have creo parametric 2.0 m070 (academic) but I didn't find the...
View ArticleRevise Action in Change Notice Only
Is there a way to remove the Revise selection from the Action menu and force them to Revise through a Change Notice? We are currently on 10.1. Thank you,Brian
View ArticleFMEA Tool Tip
When adding a new Mode into a FMEA Worksheet how can i select certain columns to 'merge and center' the data in that feild without adding another line/row? Any information will be uselful many thanks.
View ArticleCreation a plot with error bars (Y and X axis)
Hello, Dear Mathcad users!It's my first lessons on mathcad prime 2.0, and I'am trying to create a plot with error bars (Y and X axis).I managed with Y-axis, but I cannot make the same on X-axis. Could...
View Articlewhat have I done.....
what have I done to cause this behavior when pulling diameter dimensions in drawings? When I pull diameter dimension for a hole in a drawing they behave this way: -the largest denominator is set...
View ArticleFMEA Failure Rate Calculation
Good afternoon, I am trying to generate functional FMEA reports for various systems comprising multiple sub-assemblies and parts. Within each FMEA System Tree under "Failure Rate Type" there is the...
View ArticleClik here to view.
Error with array dimensions
Hello everyone, I'm trying to square the the values in a non-square matrix in a function. In order to do this, I use the vectorize operator above the operation (squaring or multiplying the radii...
View ArticleBad mate in wide chassis
I think there is a problem with the Creo model set I downloaded from the PTC FIRST site. The toughbox on back side of AM14U Wide assembly is too low. Looks like output shaft is mated to lower bearing...
View ArticleSchematics
Hello, I do not know much about the Creo Schematics. My company uses Eagle and Gerber files. With Creo Schematics software, can I import in Eagle and Gerber files into Creo Schematics? Can I export...
View ArticleOld Chain Drive modelling
Hi all Modelling a 1957 Trawler Gearbox, most bits are OK but I am a little worried about tackling the chain drive elements. Has anyone any experience of modelling single and double chain drives, got...
View ArticleIs it possible to develop a MS Word Import Map Template for S1000D?
Hi, Basically I just want to know whether anyone has created an Import Map Template to import MS Word files into Editor S1000D modules? Is it possible and how difficult is it when compared to creating...
View ArticleDisplay of integrals
As part of a Mathcad sheet, I wish to include a short section on the derivation of an equation. This involves a definite integral. I can write the initial integral with limits, and can write the...
View ArticleAssembly references
Hello all, I have a assembly I am using. The parts I started using for the assembly got moved to different folders on accident and now the assembly cant find the files to use. Is there a way to tell...
View ArticleShow list of users in "Add Participants" when I creat a new discussion
Hi guys! I am trying to create a discussion and add participants.But When I click in "add" it shows me two options, team and all participants.But the both options shows me the same thing (only groups)...
View ArticleDownloading full Creo 3.0 Braun demo set
Does anyone know can I download the full Creo 3.0 Braun demo set from PTC's demo part of Windchill or do I have to download each module one at a time? One at a time will be very disjointed and time...
View ArticlePTC Mathcad Prime: Past, Present, Future
Here is a link to blog from PTC regarding Prime 3.1, details of Prime 4.0 and 5.0. http://blogs.ptc.com/2014/09/15/ptc-mathcad-prime-past-present-future/ They outline the features which are to included...
View Article