2015 Kit of Parts CAD files
Will there be CAD files for the 2015 kit of parts and game pieces from PTC, or did these come from First in past years?Thanks so much
View ArticleClik here to view.
Creo 3.0 Installation
Afternoon Guys, I am after the collective wisdom/assistance in the installation of Creo 3.0, I have downloaded the zip folder, then proceeded to disable my anti-virus/firewalls. This has been done in...
View ArticleSolution ever found for Running Mathcad 6.0 in Windows 7?
It works just fine except you cannot create or save a new file; Mathcad just closes/crashes. Yeah, I know how old 6.0 is. I use version 13 quite a bit but want to use 6.0 on my laptop. Thanks for any...
View ArticleClik here to view.
How to correct the Pell(n) function ? (for n = 181)
Hello Everyone, How to correct the Pell(n) function ? ( for n = 181) Thanks in advance for your time and help. Regards.
View Articlein promotion request need to go back to intial screen to approve
When approving a change task/promotion request you need to go back a few screen to approve once you pressed the link to investigate the cad files.this wasnt the situation in 9.1.any plans to fix?
View ArticleUnable to find license key for trail version and CMS connector details
Hello All, I have downloaded and setup the Arbortext editor trial version and trying to configure the CMS (Documentum) need following document, can someone provide the same unable to access....
View ArticleCAD-Product into Microsoft Visio
Is it possible to export a Product tree from a Windchill CAD-Product into Microsoft Visio.
View ArticleClik here to view.
range -> equal to ->vector
Sorry if this was alrady mentioned, but it seems this might be mentioned here. I was confused whaen pressing equal to in order to imediate evaluate a range variable. In Mathcad 15 it becomes a vector...
View ArticleInstalled Creo 2.0 wont run without admin rights?
Hi all, We have just installed Creo 2.0 with the license server method.The software loads when run as an admin level user but not when run as a non admin user.We have done the step of adding full file...
View ArticleCan an optimization analysis take LDA´s "user defined output steps"...
Hello all I need to run an optimization analysis that requires LDA. The goal is to minimize or maximize a specific measure whatever is its value in any of the "user defined output steps". _ Hopefully...
View Article"im editissue" is not working using Java APIs.
Hi, I am updating an Item using java program but getting "null" response. Please help me with below code. Command cmd = new Command(); cmd.setApp(Command.IM); cmd.setCommandName("editissue");...
View Articlehas anyone found a fix for the dim_fraction_denominator for diameter dimensions
here is the case 12253254 and here is an earlier thread. http://communities.ptc.com/message/258156#258156 also is anyone else having this issue? thank you, JG
View Articlewhat have I done.....
what have I done to cause this behavior when pulling diameter dimensions in drawings? When I pull diameter dimension for a hole in a drawing they behave this way: -the largest denominator is set...
View ArticleClik here to view.
La fonction Lock
Bonjour à tous et toutes les membres de PTC et je vous souhaite une trés bonne année 2015 J'ai une question concernat la fonction Lock de Life Cycle.On faite je comprend pas vraiment l'utilité de la...
View ArticleClik here to view.
Diameter Dimension in Drawing View (Creo 3.0)
Can anyone bring me up to speed on how to create the diameter dimension shown below correctly? In 2.0, I could pick a point, then the centerline, then the point again and get the diameter. In version...
View ArticleIs there any way to open student edition files on commercial version
Hello, I am the CAD mentor for one of the First teams and we have been using the student edition of Creo.Being a small school, resources are very limited. Not only computers, they don't have a student...
View ArticleChange Management Customization
Does anyone have a detail, concise document on the steps to customize the change management forms and workflow associated with change request?Things that we have identified to change are the change...
View ArticleClik here to view.
Modifying Group Access Rights
Hi Everyone, How do I modify the rights for Groups in the Manage Security screen? Right now, all the checkboxes are disabled. Thanks,
View ArticleU3D PDF Model Based Definition
Hi, I am running Creo 2.0. We are currently looking into Model Based Definition (no 2-d drawings) for our manufacturing parts. I have been reading a lot on the subject as well as playing around a bit...
View ArticleCreo 2 drawing dimension tolerance
I want to set the tolerances of individual dimensions on a drawing. I have the following two lines set in my config.pro: tol_display yestol_mode nominal Two items: 1. Creo doesn't like the "tol_mode...
View Article